page 1 of 5 product overview mini-circuits CMA-103+ is an advanced wideband amplifer fabricated using e-phemt technology and offers extremely high dynamic range over a broad frequency range and with low noise fgure. in addition, the CMA-103+ has good input and output return loss over a broad frequency range without the need for external matching components and has demonstrated excellent reliability. the amplifer is bonded to a mul - tilayer integrated ltcc substrate, then hermetically sealed under a controlled nitrogen atmosphere with gold-plated cover, eutectic au-sn solder, and ni-pd-au termination fnish. cma-series amplifers have been tested to meet mil requirements for gross leak, fne leak, thermal shock, vibration, acceleration, mechani - cal shock, and htol. feature advantages hermetically sealed ideal for use anywhere long-term reliability adds bottom-line value: high moisture areas, busy production lines, high-speed distribution centers, heavy industry, outdoor settings, and unmanned facilities, as well as military applications. broad band: 0.05 to 4.0 ghz broadband covering primary wireless communications bands: cellular, pcs, lte, wimax ultra high ip3 versus dc power consumption: 45 dbm typical at 2 ghz at +5.0v supply voltage and only 97ma the CMA-103+ provides excellent ip3 performance relative to device size and power consumption. the combination of the design and e-phemt structure provides en- hanced linearity over a broad frequency range as evidence in the ip3 being typically 20 db above the p 1db point. this feature makes this amplifer ideal for use in: ? driver amplifers for complex waveform up converter paths ? drivers in linearized transmit systems ? secondary amplifers in ultra high dynamic range receivers low noise figure: 0.5 db up to 1.0 ghz a unique feature of the CMA-103+ which separates this design from all competitors is the low noise fgure performance in combination with the high dynamic range. ceramic, hermetic package low inductance, repeatable performance, outstanding reliability in tough operating con- ditions, and small size (0.12 x 0.12 x 0.045) key features 50 ? ? 0.05 to 4 ghz the big deal ? ceramic, hermetically sealed, nitrogen flled ? low profle case, 0.045 ? ultra high ip3 ? broadband high dynamic range CMA-103+ case style: dl1721 ultra linear low noise, ceramic monolithic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com
page 2 of 5 simplifed schematic and pad description function pad number description rf in 3 rf input pin. this pin requires the use of an external dc blocking capacitor chosen for the frequency of operation. rf-out and dc-in 6 rf output and bias pin. dc voltage is present on this pin; therefore a dc blocking capacitor is necessary for proper operation. an rf choke is needed to feed dc bias without loss of rf signal due to the bias connection, as shown in recommended ap - plication circuit, fig. 2 gnd 7, paddle connections to ground. use via holes as shown in suggested layout for pcb design to reduce ground path inductance for best performance. nc 1,2,4,5,8 not used internally. connected to ground on test board product features ? ceramic, hermetically sealed, high reliability ? low profle case, .045 high ? 5v/3v operation ? high ip3, 45 dbm typ. at 2 ghz, vd=5v ? low noise figure, 0.5 at 1 ghz; 0.8 db at 2 ghz ? gain, 10.9 db typ. at 2 ghz ? p1db 23.1 dbm typ. at 2 ghz at vd=5v rev. or m169661 CMA-103+ bt/cp/am 180919 general description CMA-103+ (rohs compliant) is an advanced wideband amplifer fabricated using e-phemt technology and offers extremely high dynamic range over a broad frequency range and with low noise fgure. in addition, the CMA-103+ has good input and output return loss over a broad frequency range without the need for external matching components. the mmic amplifer is bonded to a multilayer integrated ltcc substrate and then hermetically sealed under a controlled nitrogen atmosphere with gold plated cover and eutectic au-sn solder. terminal fnish is ni-pd-au. it has repeatable lot to lot performance due to tightly controlled semiconductor and assembly processes. these amplifers have been qualifed to mil requirements and have been tested for hermeticity. typical applications ? high rel systems ? defense and aerospace ? base station infrastructure ? portable wireless ? catv & dbs ? mmds & wireless lan ? lte rf-in rf-out and dc-in gnd 1 4 3 2 8 5 6 7 gn d r f i n nc gn d nc r f out, dc t op vie w nc nc nc 0.05-4.0 ghz CMA-103+ case style: dl1721 ultra linear low noise, ceramic monolithic amplifer notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com +rohs compliant the +suffix identifies rohs compliance. see our web site for rohs compliance methodologies and qualifications
page 3 of 5 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com parameter ratings operating temperature (ground lead) -40c to 125c storage temperature -65c to 150c operating current at 5.0v 200 ma power dissipation at 5.0v 1w input power (cw) +21 dbm (50 to 2000 mhz) +26 dbm (2000 to 4000 mhz) dc voltage on pin 7 6v note: permanent damage may occur if any of these limits are exceeded. electrical maximum ratings are not intended for continuous normal operation. absolute maximum ratings electrical specifcations (1) at 25c, 50 , unless noted CMA-103+ (1) measured on mini-circuits characterization test board tb-829-103+. see characterization test circuit (fig. 1) (2) current increases at p1db parameter condition (ghz) vd=5v vd=3v units min. typ. max. typ. frequency range 0.05 4.0 ghz gain 0.05 26.3 25.7 db 0.4 22.1 21.7 1.0 14.7 16.3 18.0 16.0 2.0 11.0 10.7 3.0 7.9 7.7 4.0 5.8 5.7 noise figure 0.05 0.4 0.3 db 0.4 0.4 0.4 1.0 0.5 0.4 2.0 0.8 0.9 3.0 1.1 0.8 4.0 1.3 1.3 input return loss 0.05 6.2 5.8 db 0.4 10.9 10.2 1.0 10.0 14.0 13.0 2.0 16.0 15.0 3.0 17.3 16.4 4.0 18.6 17.3 output return loss 0.05 12.9 13.0 db 0.4 19.9 21.8 1.0 14.0 18.2 22.1 2.0 16.4 19.9 3.0 15.2 18.2 4.0 14.5 17.1 reverse isolation 1.0 21.1 20.3 db output power @1db compression (2) 0.05 20.0 15.6 dbm 0.4 22.1 18.6 1.0 22.2 18.9 2.0 23.1 19.7 3.0 23.5 20.3 4.0 24.2 20.9 output ip3 0.05 37.4 34.9 dbm 0.4 39.4 32.8 1.0 42.6 33.2 2.0 40.0 44.8 33.9 3.0 47.1 34.3 4.0 47.9 35.0 device operating voltage 4.8 5.0 5.2 3.0 v device operating current 97 120 60 ma dc current variation vs. temp. -178 -54 a/c dc current variation vs. voltage 0.014 0.018 ma/mv thermal resistance, junction-to-ground lead 61 61 c/w monolithic e-phemt mmic amplifer
page 4 of 5 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com CMA-103+ monolithic e-phemt mmic amplifer cma - 103+ monolithic e - phemt mmic amplifier notes a. performance and quality attributes and conditions not expressly stated in this specification document are intended to be excl uded and do not form a part of this specification document. b. electrical specifications and performance data contained in this specification document are based on mini - circuit?s applicable established test performance criteria and measurement instructions. c. the parts covered by this specification document are subject to mini - circuits standard limited warra nty and terms and conditions (collectively, ?standard terms?); purchasers of this part are entitled to the rights and benefits contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mi ni - ci rcui t s? website at www.minicircuits.com/mclstore/terms.jsp mini - ci r cuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235 - 0003 (718) 934- 4500 sales@minicircuits.com page 4 of 5 tb - 829 - 103+ zx85 - 12g - s+ mcl cma - 103+ characterization test circuit suggested pcb layout (pl - 602) vcc (supply voltage) rf - in rf - out fig 1 . block diagram of test circuit used for characterization. (dut tested on mini - circuits characterization test board tb - 829- 103+ ) gain, return loss, output power at 1db compression (p1 db) , output ip3 (oip3) and noise figure measured using agilent?s n5242a pna - x microwave network analyzer. conditions: 1. gain and return loss: pin= - 25dbm 2. output ip3 (oip3): two tones, spaced 1 mhz apart, 5 dbm/tone at output. recommended application circuit cblock=0.001f, bias - tee=tcbt - 14+, cbypass=0.1f fig 2a . evaluation board tb - 988- 103+ includes case, connectors and components soldered to pcb product marking ceramic body model 3 6 7 , paddle
page 5 of 5 notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp mini-circuits ? www.minicircuits.com p.o. box 350166, brooklyn, ny 11235-0003 (718) 934-4500 sales@minicircuits.com CMA-103+ esd rating human body model (hbm): class 1a (250 to <500v) in accordance with ansi/esd stm 5.1 - 2001 machine model (mm): class m1 (25v) in accordance with ansi/esd stm5.2-1999 msl rating moisture sensitivity: msl1 (these parts are hermetic, air cavity and therefore, msl ratings do not strictly apply. for handling purpose, use msl1) additional detailed technical information additional information is available on our dash board. to access this information click here performance data data table swept graphs s-parameter (s2p files) data set (.zip fle) case style dl1721 ceramic package, exposed paddle, terminla fnish: nipdau tape & reel f66-1 standard quantities available on reel 7 reels with 20, 50, 100, 200, 500 or 1k, 2k devices. suggested layout for pcb design pl-602 evaluation board tb-988-103+ environmental ratings env-68 3wcnkecvkp6guvkpi test description test method/process results 1 hermeticity (fne and gross leak) mil-std-202 method 112, cond. c & d pass 2 acceleration, 30kg, y1 direction mil-std-883 method 2001 cond. e pass 3 vibration , 10-2000hz sine, 20g, 3 axis mil-std-202 method 204, cond. d pass 4 mechanical shock mil-std-202 method 213, cond . a pass 5 pind 20gs @130 hz mil-std-750 method 2052.2 pass 6 temp cycle -55c/+125c, 1000 cycles mil-std-202 method 107 pass 7 autoclave, 121c, rh 100%, 15 psig, 96 hrs jesd22-a102c pass 8 htol, 1000hrs, 105c at rated voltage condition mil-std-202 method 108, cond . d pass 9 bend test jesd22-b113 pass 10 resistance to soldering heat, 3x refow, 260c peak jesd22-b102 pass 11 drop test jesd22-b111 pass 12 adhesion strength push test>10 lb pass additional notes a. performance and quality attributes and conditions not expressly stated in this specifcation document are intended to be excluded and do not form a part of this specifcation document. b. electrical specifcations and performance data contained in this specifcation document are based on mini-circuits applicable established test performance criteria and measurement instructions. c. the parts covered by this specifcation document are subject to mini-circuits standard limited warranty and terms and conditions (collectively, standard terms); purchasers of this part are entitled to the rights and benefts contained therein. for a full statement of the standard terms and the exclusive rights and remedies thereunder, please visit mini-circuits website at www.minicircuits.com/mclstore/terms.jsp monolithic e-phemt mmic amplifer
|
